E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP - Replaced The Screen, Now Only 1MB RAM is Recognized : /

Welcome, Guest. Please login or register.
Did you miss your activation email?
August 17, 2017, 04:32:35 AM
Home Help Search Login Register
News: Want to register? Then please don't use a Hotmail, Yahoo or Gmail address. They'll block the activation email.
Still having problems activating your account? Send an email to: EIII @ telenet.be

+  E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP
|-+  General Category
| |-+  EIII XP Technical Issues / Tips
| | |-+  Replaced The Screen, Now Only 1MB RAM is Recognized : /
« previous next »
Pages: [1] Print
Author Topic: Replaced The Screen, Now Only 1MB RAM is Recognized : /  (Read 312 times)
edude
Jr. Member
**
Offline Offline

Posts: 26



« on: July 04, 2017, 02:47:18 PM »

i replaced the screen with an oled, and it works fine

however i made a few booboos (i lightly accidentally scratched a few traces) or maybe shorted something because now it will only recognize 1MB of RAM

also i can't save the os onto floppy, it returns errors when it tries to write

also, some sounds i did manage to load were corrupted and were digital noise. only a few though, otherwise it is ok

also, where before if there was no scsi termination i could not get past the startup screen, now it will flash the error for a split second then go on to load the os

i think i messed this eiiixp up : / none of these errors happened before i replaced the screen

any ideas? this was my backup and i would hate to sell it
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #1 on: July 04, 2017, 03:10:18 PM »

i just noticed this though, under where the inverter was

i moved the part a bit when i desoldered it and it seems to have scratched the trace. this trace goes left and to the ram section btw



* trace.JPG (287.39 KB, 885x649 - viewed 20 times.)
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #2 on: July 04, 2017, 05:38:22 PM »

a close up


* trace2.JPG (3234.92 KB, 4608x3456 - viewed 22 times.)
Logged
Wolfram
Full Member
***
Offline Offline

Posts: 93


« Reply #3 on: July 05, 2017, 02:46:56 AM »

Nice cut. ;-)
Remove carefully the lacquer and put a small drop solder on it.
You can measure functionality from the end to end of the trace.
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #4 on: July 05, 2017, 03:56:06 AM »

thanks : )

i cleaned the trace and it is not cut. the inverter had caused some residue/corrosion but it is still intact

now it won't even boot up, first it shows the preset definition light for a few seconds then just flashes all lights and no screen
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #5 on: July 06, 2017, 05:52:01 AM »

dag namnit, flew too close to the e-mu on wings of noobishness

anybody know what the preset definition diagnostic light means?
Logged
Wolfram
Full Member
***
Offline Offline

Posts: 93


« Reply #6 on: July 06, 2017, 08:13:47 AM »

Verify the cable connection to the panel board.
Measure the connection from end to end.
Be sure pin 1 is connected to pin 1.
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #7 on: July 08, 2017, 07:19:50 AM »

i test using a multimeter yes?
« Last Edit: July 08, 2017, 07:21:32 AM by edude » Logged
Wolfram
Full Member
***
Offline Offline

Posts: 93


« Reply #8 on: July 08, 2017, 09:05:13 AM »

yes, turn of the EIII set the multimeter to Continuity beeper and check the connection from end to end.
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #9 on: July 09, 2017, 10:50:46 AM »

isn't that just checking the cable though? checking pin 1 on panel and pin 1 on main board with cable between only checks the cable for continuity yes?
Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #10 on: July 11, 2017, 03:33:03 PM »

i checked as many traces as i could on the panel and they are ok, but still not sure what you say
Logged
obsoletemachines
Jr. Member
**
Offline Offline

Posts: 20


« Reply #11 on: July 27, 2017, 02:51:25 AM »

hi,
i don't think there is damage to the trace from the photos you sent...the traces run quite deep in this pcb and are not just 'stencilled' on to the PCB.

I think you need to go back to basics and test the power rails first.. what are you getting there.

If the power is ok then something is probably shorting the RAM circuitry - did you drop anything into the board?  Re-seat the ram chips... they may be slightly dislodged. But first as i say check the rails.

Logged
edude
Jr. Member
**
Offline Offline

Posts: 26



« Reply #12 on: August 09, 2017, 11:38:37 AM »

hi,
i don't think there is damage to the trace from the photos you sent...the traces run quite deep in this pcb and are not just 'stencilled' on to the PCB.

I think you need to go back to basics and test the power rails first.. what are you getting there.

If the power is ok then something is probably shorting the RAM circuitry - did you drop anything into the board?  Re-seat the ram chips... they may be slightly dislodged. But first as i say check the rails.



thanks  Smiley

i could try soldering the inverter back on and swapping the front panel with one from another eiiix just to test, although since the problems are with ram among other things it may be the main board as you say? the ram chips are soldered on btw i believe

i am not experienced to do anything much besides check the rails, but by rails do you mean the main power rails going to the drives? i'm not sure how to check any other than those
Logged
Pages: [1] Print 
« previous next »
Jump to:  


Login with username, password and session length

E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP - Replaced The Screen, Now Only 1MB RAM is Recognized : /

SEO light theme by © Mustang forums. Powered by SMF 1.1.21 | SMF © 2015, Simple Machines