|
Title: EIIIX OLED DISPLAY Post by: powmax on September 12, 2013, 11:42:33 AM The Newhaven NHD-0420DZW-AY5 fits also the EIIIx Sampler Series
(http://www.uzz40.de/IMAGES/EIIIX_DISPLAY_0000.jpg) (http://www.uzz40.de/IMAGES/EIIIX_DISPLAY_0001.jpg) (http://www.uzz40.de/IMAGES/EIIIX_DISPLAY_0002.jpg) (http://www.uzz40.de/IMAGES/EIIIX_DISPLAY_0003.jpg) regards marcus Title: Re: EIIIX OLED DISPLAY Post by: kdk on September 12, 2013, 01:26:39 PM That looks great!!
Title: Re: EIIIX OLED DISPLAY Post by: edude on September 19, 2013, 06:26:57 AM boo-ya!
Title: Re: EIIIX OLED DISPLAY Post by: Mr Mode on October 09, 2013, 01:56:13 PM I've installed the Newhaven NHD-0420DZW-AY5 in my EIII XS. Aside from some initial desoldering, the installation was a breeze. Highly recommended.
Title: Re: EIIIX OLED DISPLAY Post by: edude on October 10, 2013, 08:38:56 AM looks amazing!
mr mode, can you tell me what cf drive you are using? i have an acard 7720 and am told to get either a startech or addonics drive? Title: Re: EIIIX OLED DISPLAY Post by: Mr Mode on October 13, 2013, 01:35:09 AM Thanks edude....it does look cool ;) WRT the CF installation, I use the Acard. It was purchased as a full solution from SCSIforSamplers in 2010, just before they disappeared off the face of the earth. The cards I use are SCSI 1 compatible Kingston 1Gb CF. I don't know what the newer options are, but this configuration has been rock solid without any issues.
Title: Re: EIIIX OLED DISPLAY Post by: barendb on February 04, 2015, 06:00:37 PM So do i remove pin 3? or just solder it in?
Just took apart my EIIIxs and removed the old Display. I have ordered the correct one from Digi-key OLED. Title: Re: EIIIX OLED DISPLAY Post by: razo on May 14, 2018, 05:22:30 AM My OLED just got dead pixels after less than 3 years of use :'( :'( :'(
Title: Re: EIIIX OLED DISPLAY Post by: Stephencl on July 14, 2018, 07:45:01 PM So do i remove pin 3? or just solder it in? Just took apart my EIIIxs and removed the old Display. I have ordered the correct one from Digi-key OLED. Remove it! Title: Re: EIIIX OLED DISPLAY Post by: suchenderxxx on November 02, 2018, 02:55:32 AM im thinking about the oled upgrade. can someone explain why pin 3 needs to be removed?
Title: Re: EIIIX OLED DISPLAY Post by: Stephencl on November 08, 2018, 12:31:56 PM Sure, it is used to adjust contrast in the E-mu wiring scheme, so it would be connected to your contrast knob. Has no use in this application.
Title: Re: EIIIX OLED DISPLAY Post by: vlazzarini on October 01, 2021, 02:03:47 PM Hi, I have a strange problem. After replacing two chips for the analog input option, the sampler boots and works but the LCD display shows lots of gibberish mixed up with only a few correct characters.
Does anyone have any suggestions? Does it look like a broken display or is it something else. the front panel buttons appear to work correctly and I can load progr |