E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP - Is a Emulator II blowing fuse worth to purchase?

Welcome, Guest. Please login or register.
Did you miss your activation email?
November 24, 2024, 12:15:28 PM
Home Help Search Login Register
News: Problems registering? Send an email to: EIII @ telenet.be (without the spaces)

+  E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP
|-+  General Category
| |-+  EII Technical Issues / Tips
| | |-+  Is a Emulator II blowing fuse worth to purchase?
« previous next »
Pages: [1] Print
Author Topic: Is a Emulator II blowing fuse worth to purchase?  (Read 3430 times)
rtech
Full Member
***
Offline Offline

Posts: 93


« on: February 19, 2010, 11:19:18 AM »

Hey everyone,

I have an opportunity to purchase an EII that is blowing the fuse, how much do you think I should pay for it? And how much are the repairs assuming that it is only the PSU?

PS, what is the going price for a fully working unit?


Thanks

Rtech
« Last Edit: February 19, 2010, 01:46:24 PM by rtech » Logged
captainjc
Jr. Member
**
Offline Offline

Posts: 21


« Reply #1 on: February 19, 2010, 12:38:43 PM »

In good condition, I've seen them go for $500-1000. Less than that I would say is a deal, especially if you don't have to ship it (HEAVY!). It depends on many factors like, how good the condition, recently serviced, how big a library (disks sell for decent money on their own if you search ebay completed), whether it's mac -> SD capable (some rev 0's and early rev 1's are not). Not sure about the PSU thing. If you search the yahoo group, I know there are people who have done it on there - possibly on here too.
Logged
rtech
Full Member
***
Offline Offline

Posts: 93


« Reply #2 on: February 19, 2010, 12:51:21 PM »

Thanks captainjc,

  I am going to go check it out later on today. The owner says that it is not functioning at all, because when you power it up it just blows the fuse. I dont think he has any disks with it. Im hoping to open it up and see if I can see any damage/burned parts. While I am at it, I will look for the Mac interface and whether it has the newer Rev 1 Board.

Thanks
Logged
captainjc
Jr. Member
**
Offline Offline

Posts: 21


« Reply #3 on: February 19, 2010, 03:19:07 PM »

Be advised, even the ones that are not mac compatible have a (totally useless) rs232 connector back there. The mac interface needs the rs422 which is in most rev 1 models. Here's some info from the yahoo group that may be of help...

> Rev.1 boards do not require the installation of an
> additional RS-422 interface board (Mac Int PCB). However, due to E-
> mu design changes several modifications are made at the factory to
> allow the Mac and Emulator to communicate. Unfortunately, these mods
> were not made at the factory to a number of Rev.1 Emulator II's.
> Check to be sure that
> the following mods have been made to the digital board:
>
> 1. The trace leading to the end of R48 closest to the back panel has
> been CUT. R48 is immediately to the left of CN12, the 25-pin
> computer connector.
>
> 2. The trace going to lC132, pin 10 has been cut. This may be
> difficult to see. The trace runs right next to the body of the IC
> socket of IC1 32, on the right side of the chip, between the middle
> and the bottom of the chip (quite near pin 10). If it has not been
> cut, or you are not sure, then lift pini 0 of 10132 up out of the IC
> socket so that nothing contacts it. Do this by removing the entire
> chip from the socket, then bending pin 10 up and re-inserting the
> chip into the socket. Pin 10 should not go into the socket.
>
> 3. If you do not have AT LEAST VERSION 2.3 of Emulator II OS
> software, then the following mod must be performed: Lift pin 22 of
> IC107 and solder one end of a 1K ohm 1/4watt 5% resistor to it.
> Solder the other end of the resistor to +5 volts DC anywhere nearby.
>
> 4. To improve data integrity, change resistor R47 on the logic board
> from 10K ohms 1/4W 5% to 1K ohms 1/4W 5%. Soldering a 1K ohm
> resistor in parallel with the existing 10K ohm resistor at R47 will
> also work.
>
> 5. Verify that the two internal EPROM's in the Emulator (MAIN and
> SCANNER) are AT LEAST Rev. 2.1. Verify that the Emulator II OS
> software being used is at least Rev. 2.2.
>
Logged
Pages: [1] Print 
« previous next »
Jump to:  


Login with username, password and session length

E-mu Emulator Sampler User Forum for the EIII EII EI and EIII XP - Is a Emulator II blowing fuse worth to purchase?

SEO light theme by © Mustang forums. Powered by SMF 1.1.21 | SMF © 2015, Simple Machines