How do i get the EII library from my PC into a MAC SE30?

[Elmbeatz]

Lennox,

HAVE YOU CHECKED

- if you either have a Rev 1 digital board inside your EII
- OR a rev 0 digital board with added RS interface

If not either one -

FORGET ABOUT IT.

[lennox]

Lennox,

HAVE YOU CHECKED

- if you either have a Rev 1 digital board inside your EII
- OR a rev 0 digital board with added RS interface

If not either one -

FORGET ABOUT IT.

yes i have the REV 1 board installed model:6050  serial 1878

should be ok i guess

[lennox]

i received the cable from Rob today. I hooked it up the modem port, started SD then powered on the emulator, selected eII front panel in SD and clicked send bank...........

can't communicate with EII         

i tried several things, appletalk on and off, restarted everything, checked if midi was on in the EMU nothing yet.

What could be wrong, please help

[dr.c]

Near the conncetor of the EII, inside, there are circuits named 4088 and 4089

They are the comm circuits. They must be toasted. Change them, they cost peanuts.

If you don't feel sure, make a picture of the circuitry around, a CLEAR AND NEAT picture (not a thumbnail at 72 dpi), and send it here, I will show you wich ones, because sometimes, tehy put equivalent circuits. For example, the Cmos circuits 4016 are pin to pin the same as 4066, the 4528 is the same as the 4098, etc ...

[lennox]

Near the conncetor of the EII, inside, there are circuits named 4088 and 4089

They are the comm circuits. They must be toasted. Change them, they cost peanuts.

If you don't feel sure, make a picture of the circuitry around, a CLEAR AND NEAT picture (not a thumbnail at 72 dpi), and send it here, I will show you wich ones, because sometimes, tehy put equivalent circuits. For example, the Cmos circuits 4016 are pin to pin the same as 4066, the 4528 is the same as the 4098, etc ...

thanks, i'm going to open it up and let you know

[lennox]

Hi Dr. C

i can't find them, here are some pictures (i hope there clear enough)

[lennox]

thanks, i hope you can point them out

[JMP]

i received the cable from Rob today. I hooked it up the modem port, started SD then powered on the emulator, selected eII front panel in SD and clicked send bank...........

can't communicate with EII         

I trust you selected modem as the communication port within Sound Designer..? (Calibrate > Serial Port > Modem)

[lennox]

i received the cable from Rob today. I hooked it up the modem port, started SD then powered on the emulator, selected eII front panel in SD and clicked send bank...........

can't communicate with EII         

I trust you selected modem as the communication port within Sound Designer..? (Calibrate > Serial Port > Modem)

yes i did, also tried the printer port

[dr.c]

I look at the diagrams, what is your board revision ?

[lennox]

I look at the diagrams, what is your board revision ?

it is rev.1
model 6050
serial 1878

[dr.c]

According to the schematics, its IC108 (1489) et IC139 (4088).

Please try to find them and make a picture of each with what is around.

Sorry, but this is for YOU, its just to be sure at a 100% !

Even if we change them for nothing, THEY WILL die, soon or late, these circuits ALWAYS do, and they are standard ones, you find them anywhere there are connectors leading to to external world, like printers, modems, etc...

[lennox]

first of all thanks for helping !

i located IC108 and IC139, the strange thing is that the IC139 socket is empty in my EMU, i noticed this earlier when i just purchased it and i looked in the forum and found out that this among a few other empty sockets is normal. But perhaps i'm mistaking?

here are the pictures, i marked IC108 with a green dot straight above and the other picture has a green dot on the empty ic139 socket



thanks again

[dr.c]

Damn... there is nothing, at R139 !!!!

What is written on the circuit IC108, the picture is saturated, unreadable.

[lennox]

this is written on IC108 top and bottom

I8348A+
DS26LS32CN