|
51
on: June 30, 2024, 04:35:27 AM
|
|
Started by Deft - Last post by Deft
|
|
Hi, I`ve PM`d you, I dont have all the PALs jedec unfortunately...
|
|
|
52
on: June 28, 2024, 04:13:52 AM
|
|
Started by Deft - Last post by Thomas Flemming
|
|
is it possible to get a new burned pal , i will pay
regards
thomas
|
|
|
53
on: June 28, 2024, 04:06:17 AM
|
|
Started by Rio - Last post by Thomas Flemming
|
|
which person have the skills to burn the EIII (all available JEDEC) pal ic for the cpu main board or know somebody a tech nerd with these skills?!?!?
my eiii will not boot, and the cpu mainboard seems to be the prob,, i changed some ic, but no luck so the pal could be the issue
,psu is overhauld. voltages are in limit, rom ic changed too,
pls contact me, how ever ,
I WILL PAY FOR
thx a lot in advance
|
|
|
54
on: June 28, 2024, 02:43:03 AM
|
|
Started by Thomas Flemming - Last post by Thomas Flemming
|
|
which person have the skills to burn the EIII (all available JEDEC) pal ic for the cpu main board or know somebody a tech nerd with these skills?!?!?
my eiii will not boot, and the cpu mainboard seems to be the prob,, i changed some ic, but no luck so the pal could be the issue
,psu is overhauld. voltages are in limit, rom ic changed too,
pls contact me, how ever ,
I WILL PAY FOR
thx a lot in advance
|
|
|
55
on: June 21, 2024, 11:52:47 AM
|
|
Started by who - Last post by who
|
I'd forgotten how good the EIII sounds! I've been loading banks all morning.  |
|
|
56
on: June 20, 2024, 02:30:04 PM
|
|
Started by who - Last post by who
|
Thanks to the thread below, I removed each card, cleaned the contacts, gently pressed on each of the socketed chips, reseated the cards in the card cage, and carefully reconnected the ribbon cables. The EIII then jumped back to life https://eiiiforum.com/index.php?topic=866.0Now all I have left is the Preset Management LED still doesn't work!  |
|
|
57
on: June 20, 2024, 02:25:09 PM
|
|
Started by nuipb - Last post by who
|
|
I think I fixed it. Once I removed each card, cleaned the contacts, gently pressed on each of the socketed chips, reseated the cards in the card cage, and carefully reconnected the ribbon cables, the EIII jumped back to life!
|
|
|
58
on: June 20, 2024, 09:10:30 AM
|
|
Started by nuipb - Last post by who
|
|
I also have the, "data & volume sliders stuck at 000" problem. In other words, when I perform the following steps, none of the sliders, wheels or pressure respond:
1. Click the Master button
2. Select 8, Special
3. Select 0
4. Enter the magic code, 1358
5. Enter 1, wait for the test sequence to display the screen where you can operate the wheels, sliders, etc. and see the values change.
As mentioned above, when I get to the final step on my EIII, none of the sliders or wheels change value. Prior to reseating the cards in the cage, the wheels, etc. worked so I assume I have a bad connection somewhere.
|
|
|
59
on: June 19, 2024, 05:28:18 PM
|
|
Started by who - Last post by who
|
|
I now have audio output, but it is just what I would describe as a UFO taking off!
|
|
|
60
on: June 19, 2024, 12:59:55 PM
|
|
Started by who - Last post by who
|
|
I just found a post suggesting a pinched ribbon cable between the front panel and the card cage can cause no output. I'll try messing with that once I get the sliders worked out.
|
|
|
